Chapter 6 of 8
Move the packet with the HD6309
Try the same transfer with a different agreement between the program and the CPU. The portable loop uses B as a counter, A as a sum, and several instructions per byte. The Hitachi processor has a block-transfer instruction and a separate count register. You can see exactly which work it takes over.
Choose both processors deliberately
Save your guest work. In Machine Settings, choose the Hitachi HD6309 processor and apply the restart. Start at the Disk BASIC prompt. In Assembly Development, open a copy of dispatch6309.asm and set the assembler’s Target to HD6309. The Machine setting chooses what executes opcodes. Target chooses what the assembler accepts. As a negative check, choose the MC6809 target and Assemble: LDW and TFM are rejected. Return the target to HD6309 before continuing.
start leax packet,pcr
leay received,pcr
ldw #size ; W counts the bytes left to transfer
copy tfm x+,y+ ; move from X to Y and increment both
inspect leax received,pcr ; stop here to inspect W, X, Y and RAM
next lda ,x+
W is a sixteen-bit register made from E (high byte) and F (low byte). D is similarly made from A and B. On the 6309, Q is the 32-bit combination D:W. The E register and the E flag in CC have different jobs. Watch W through E and F if the inspector shows the halves separately.
Cross the transfer in one debugger step
Set a stop on copy, choose Run, and look up packet and received in Symbols. At TFM, X points at the first input byte, Y at the first destination byte, and W is 3. Predict the pointer values after the copy. Step once, then inspect the four bytes at received in Mapped CPU.
| Value | At copy | At inspect |
|---|---|---|
| PC in this build | $3F0C | $3F0F |
| X | $3F28 | $3F2B |
| Y | $3F2B | $3F2E |
| W | $0003 | $0000 |
| Four destination bytes | 00 00 00 00 | 4F 52 42 00 |
TFM X+,Y+ copies a byte, advances both pointers and counts down W. In VCC Plus the debugger presents this transfer as a whole instruction. The stop after it is where you compare the buffers. Continue prints ORB and returns. W supplied the count, and the fourth zero came from the original buffer declaration. This version never computes a checksum. Comparing its total run time with the first receiver would mix two different jobs.
Observe native mode, then give BASIC its mode back
The HD6309 can execute the preceding instructions in its startup compatibility mode. Native mode is a separate processor setting with effects including interrupt frames and instruction timing. To observe the distinction, use a freshly restarted HD6309 Disk BASIC guest. Save and open mode.asm. Set a stop on native and choose Run. The exercise assumes the reset value MD=$00. It saves CC and masks IRQ and FIRQ during its short mode-changing section. Keep it as supplied and let it finish.
start pshs cc ; remember BASIC's interrupt masks
orcc #$50 ; mask IRQ and FIRQ for the short experiment
ldmd #1 ; select 6309 native mode
native ldw #$1234 ; inspect MD, then step and read E and F
ldmd #0 ; restore reset mode before calling BASIC
restored puls cc ; restore the caller's condition codes
rts
At native the instruction that selects mode 1 has executed. In the Debugger’s HD6309 registers inspect MD. Step LDW: E becomes $12 and F becomes $34. Step LDMD #0. At restored, MD reads $00 while the data in W still represents $1234. Continue restores the saved condition codes and returns to BASIC. Enter PRINT 2+3 to check that the guest is listening again.
Changing mode around an unknown interrupt handler would give that code a different environment. In particular, a full native-mode interrupt frame includes E and F. The interrupt experiment starts from a known mode and lets you inspect an actual frame. If you interrupt the mode experiment and lose your place, restart the disposable guest before continuing the book.